|
|
Post by carlos4x4sand on Dec 28, 2003 3:57:57 GMT -5
Is there a toyota front bench seat that is either 60/40 or 50/50? I have a Runner and would like to add another seat, but be able to move only the front passenger seat inorder on get in the back.
|
|
NCSU
Full Member
'94 Pickup 22RE, 2"body lift, 33x12.50 BFG A/T's, RS5000's, K&N, Airbox mod, Flowmaster-2.5"pipe
Posts: 245
|
Post by NCSU on Dec 28, 2003 11:44:22 GMT -5
In my '94 Pickup there is a 60/40 seat setup. I am able to move both seats forward to access the extended cab. But, the drivers seat is limited in its travel forward because of the steering wheel. Passanger seat slides all the way up.
|
|
|
|
Post by carlos4x4sand on Dec 28, 2003 14:41:38 GMT -5
Thats cool, i like the idea of a 60/40 better. Do u think that they are a direct bolton?
|
|
NCSU
Full Member
'94 Pickup 22RE, 2"body lift, 33x12.50 BFG A/T's, RS5000's, K&N, Airbox mod, Flowmaster-2.5"pipe
Posts: 245
|
Post by NCSU on Dec 28, 2003 15:17:42 GMT -5
honestly, I am not sure. I have never looked at the bolt patter of the 2nd generation 4Runners. But, I am sure somebody on here has done it before. I remember reading somewhere that the 4Runner seats that are individual (as opposed to the 60/40) went in to the Pickups with only having to drill one extra hole. So, I guess you would end up having an extra hole in your floor board that you might have to just plug up or leave it if you don't care.
|
|
|
|
Post by carlos4x4sand on Dec 28, 2003 15:22:21 GMT -5
On ur seats do they have anykind of armrest?
|
|
NCSU
Full Member
'94 Pickup 22RE, 2"body lift, 33x12.50 BFG A/T's, RS5000's, K&N, Airbox mod, Flowmaster-2.5"pipe
Posts: 245
|
Post by NCSU on Dec 28, 2003 20:10:48 GMT -5
Yeah, there is a little armrest that folds up into the seat. I will snap a picture tomorrow and post it on here if you want so you can see how it looks.
|
|
|
|
Post by carlos4x4sand on Dec 28, 2003 21:41:24 GMT -5
Sure that would be good
|
|
|
|
Post by dunphy on Dec 29, 2003 19:35:02 GMT -5
I don't think it will match up complety, the passenger seat will but i'm not sure about the drivers seat. I just took the 60/40 seats out of my truck yesterday and put in sr5 bucket seats from a 4runner. The passenger seat was a direct bolt in, but the driver seat uses 2 of the same mounts on the outside next to the door but the inside mounts are different. Going from bench to bucket the drivers side bucket uses the seat belt mount from the bench for the rear and there is no hole for the front. Where i didn't have all the mounts the bucket i'm assuming you might not have all the mounts for a bench, though i'm not positive.
By the way the buckets are alot more comfortable then the 60/40 seats.
|
|
|
|
Post by carlos4x4sand on Dec 29, 2003 19:40:30 GMT -5
Well i dont care for comfort, i would like more people space. Dunphy, What are u gonna go with ur 60/40s?
|
|
NCSU
Full Member
'94 Pickup 22RE, 2"body lift, 33x12.50 BFG A/T's, RS5000's, K&N, Airbox mod, Flowmaster-2.5"pipe
Posts: 245
|
Post by NCSU on Dec 29, 2003 20:38:40 GMT -5
|
|
|
|
Post by carlos4x4sand on Dec 29, 2003 21:48:07 GMT -5
Now that i look at ur pics, I think about just gettn the 60 part, and doin what i need to do to make it fit. Thanx for the pics NCSU.
|
|
NCSU
Full Member
'94 Pickup 22RE, 2"body lift, 33x12.50 BFG A/T's, RS5000's, K&N, Airbox mod, Flowmaster-2.5"pipe
Posts: 245
|
Post by NCSU on Dec 29, 2003 22:10:53 GMT -5
no problem, I hope they helped
|
|
